Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
Every person has their personal piece of advice about How to Install a Bathtub Yourself.
Mounting a bath tub isn't precisely rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is readily obtainable, the project can relocate quickly; if you have to open up a wall surface to eliminate the old tub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have qualified on your own for the job as well as fit trying it. As opposed to employing a specialist to take over a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually already purchased a brand-new bathtub and do not require to change the setup of your previous water pipelines.
Your tools as well as material list need to consist of the following:
Planning for the Setup
To start with, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before proceeding to fit the new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the level and adjusting the feet on the tub until the level reads degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water and inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in place with the producer given backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, causing issues with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about How to Install a Bathtub Yourself? Put a short review below. We would be pleased to hear your opinion about this blog. Hoping that you visit us again in the near future. If you appreciated our article plz remember to pass it around. Thanks so much for taking the time to read it.
Expert diagnostics offered. Report this page